post01

gas fired glass melting furnace

Purchased equipment: gas fired glass melting furnace
Location: WUXI China
Telephone: +86 13861509127
E-mail: lexie@zozen.com
Contact us for more details about our boilers, solutions and services.

High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ and reduce heat lost.Sufficient steam storage room and heating area to generate high quality steam and high thermal power.Condenser is added to recycle the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce flue gas emission temperature and increase the thermal efficiency over 98% and save operating cost.

Environmental protection

Big combustion chamber equipped with Low emission combustion burner effectively reduce the NOx to 30mg/m3. Smoke duct and smoke outlet use internal insulation to reduce operating noise.

Combustion chamber uses full membrane water cooling wall structure and pressurized combustion without smoke mixture.

Energy conservation

Good quality alumina silicate fiber and fire clay insulation material are used and the boiler body temperature is controlled below 45℃ and greatly heat loss is reduced. Combustion chamber is designed with narrow distance tube membrane water cooling wall which has good air proof to reduce heat lost and increase boiler thermal efficiency. Internal inspection holes uses high-alumina refractory and manhole cover seal devices, solving superheat problem in this part caused by using refractory bricks.

CNC manufacturing technology

The key processing technologies such as steel plate blanking, circling, drum and tube plate drilling adopt advanced CNC machining to reduce the assembly stress and prolong the service life of the boiler.

Steel tube cutting, thread tube pressing and convection tube processing all adopt advanced CNC technology.

Automatic production line.

Leave a Comment

pro_first

Glass Melting Technology - Nikolaus SORG GmbH & Co.

Float glass furnaces with a melting capacity of 700 t/24 h or more are an integral part of the pro-gramme, as is the smallest opal glass furnace for lighting ware, with a capacity of 1 t/24 h. Not only soda-lime glass, but also lead-free crystal, full lead crystal, opal and borosilicate glasses of differing compositions and water glass are

Gas Fired Glass Melting Furnaces - Buy Furnace,Glas

Due to its high flexibility and low energy consumption, the regenerative end fired furnace is the type of furnace mostly used for container glass, table ware, cosmetic glass, pharmaceutical glass, sheet glass, solar glass, sodium-silicate glass, tubing and lighting glass. Its melting range is normally from 50 – 400 t/d.

Cross Fired Furnace - Capabilities | Horn Glass Industries

Similar to the end fired furnace, the regenerative cross fired furnace provides low energy consumption and high flexibility in terms of pull change. However, this type of furnace can be built with bigger melting areas due to the shorter flame length compared to the end fired furnace.

Glass production - Wikiped

The furnaces are natural gas- or fuel oil-fired, and operate at temperatures up to 1,575 °C (2,867 °F). The temperature is limited only by the quality of the furnace’s superstructure material and by the glass composition. Types of furnaces used in container glass making include 'end-port' (end-fired), 'side-port', and 'oxy-fuel'.

Prium® Melt EF (End Fired Regenerative Furnace) - Fives i

The Prium ® Melt EF (End Fired) Regenerative Furnace is a cost effective solution to medium size furnaces for a wide range of glass compositions and qualities. The furnaces use conventional oil or gas heating with the regenerative system to recover residual heat from the waste gases.

IMI-NFG Course on Processing in Glass - Lehigh Universi

IMI-NFG Course on Processing of Glass - Lecture 3: Basics of industrial glass melting furnaces mathieu.hubert@celsian.nl 11 Designations of glass furnace components (tank furnace, cross fired,

Glass melting furnace - Blaa

A Blaauw glass melting furnace is one-of-a-kind. With our advanced controller, your furnace will follow both your temperature curve and control the glass melting process evenly in every part of the furnace.

melting-furnace | Horn Glass Industries

melting-furnace HORN, with its extensive experience, knowledge and expertise, designs different types of furnaces best suited to the various glass melting processes. End Fired Furnace

Home - Falorni Glass Furnac

Falorni Glass since 1958 produce and customize glass furnaces. With more of 250 furnaces in operation all over the world has tailored solution.

Melting and Holding Furnaces | Home - Naberther

Exhaust Gas Discharge over the Crucible Edge. Exhaust gas discharge over the crucible edge is the standard design for our gas and oil-fired cruicible furnaces, except for the TB models for furnace temperatures of 1200 °C, since these furnaces are normally used as holding furnaces.

Glass Furnaces | Glass Melting Furnace by CM Furnac

CM’s Glass Melting Furnaces come in all form factors regardless of temperature range Useful Options for a Glass Melting Furnace. Batch processing of glass in a furnace is facilitated when the furnaces used provide a number of important options for your particular glass melting process.